Hi,
Is there a document/brief that shows all the supported functions on the 8950 QAT plug in card?
Thanks,
Jackson
↧
Intel QuickAssist Technology - Supported Functions
↧
NUC6i3SYH with Windows Server 2012 R2 and Server 2016: "no intel adapters are present"
I'm trying to install windows server 2016 standard, or 2012 R2 standard on a NUC6i3SYH but can't get the ethernet adaper to install correctly. I tried the latest 2012 R2 driver, windows 8, and windows 10 driver, and all say "cannot install the drivers. no intel adapters are present" when trying to install! Any suggestions?
↧
↧
XL710 with quad port 10Gb break cable not working in ESXi 6.5, system doesn't see 4 10Gb adapters
I have a server with ESXi 6.5 installed and an Intel XL710 Adapter with the 1 meter breakout cable to give me four 10Gb connections. My ESXI server only sees the two 40Gb ports and not the 10Gb connections. How can I fix this? I need to use the 10Gb connections individually. Thanks.
↧
How do you enable promiscuous mode on l219-LM updating drive does not seem to help
l219-LM using wireshark or NI observer same results nic is not in promiscuous mode OS Windows 10
↧
Latest Intel Network Connections versions - NCS2Prov.exe constantly generating millions of I/O calls scanning the C drive for all *.INF files
Platform is a Dell E6520 Latitude
NIC is the Intel 82579LM GigE
Windows 7 Enterprise x64, fully patched and up to date
Drivers are the latest available from the Intel site.
After updating to the latest version of the Intel Network Connections (INC) v20.7, 201.0 and 21.1 there is a problem when
the Configure button in the NIC properties is selected. Among other things this launches the ncs2prov.exe with this command line.
"C:\Program Files\Intel\NCS2\WMIProv\NCS2Prov.exe" -Embedding
This program spends the next several minutes issuing millions of I/O calls to enumerate items in the registry and then scan what appears to be most of the C: drive looking for every *.INF it can find among other things...
Tracing this with ProcMon from the MS System Internals tools counts >3.5 million events just from launching the program. If the machine did not have an SSD, this process would have likely taken a VERY long time in the range of tens of minutes at least I would think. As it is, it takes a minute or two where the machine appears to be not responding to the Configure request at first launch.
I have tried all three of the latest versions as describe, but they all have the same issue. Once the program is loaded finally, selecting a different tab starts the same behavior over again and a single tab can take minutes to display and update. A tab change generates about 2.1 million events each time...
Does anyone know how to stop this behavior? Why is it scanning the entire C: drive looking for *.INF files? It is not actually reading their contents most of the time that I can see, it just rescans the C: looking for them.... I know what the .INF and .CAT files are for and generally understand at least the basics of installing drivers and their support files.
It does not appear that it actually has anything to do with the hardware platform, but is a problem with the INC software running on Windows 7 x64.
Any thoughts as to how to stop this would be appreciated. We can switch back to even older versions, if we knew where the problems were introduced. Apparently this has existed for a year or maybe more based on the version we have tested thus far. The drivers overall work well and are much better that the official Dell drivers which do not allow most of the hardware features of the NIC driver to be exposed. (RSS, R/W buffers, TCP checksum off-loads, disable EEE, etc...) They are performing at ~60% of the network wire speed instead of about 35% with the OEM drivers.
Thank you,
-CoreyMac
↧
↧
Intel i210 vs. i219 - Do they both support VLAN Tagging?
I am planning on getting a Asrock Rack E3C236D2I server motherboard, and the two on-board gigabit NIC's it has are the Intel i210 and the intel i219.
Just want to check both the i210 and the i219 both support VLAN tagging. Planning on using Windows Server 2016 essentials.
Also what is the difference between the i210 and the i219 Chipsets?
Regards: Elliott.
↧
X710 MAC Filtering
Hi,
I have a system with an Intel X710 (supermicro onboard card).
There is a somewhat unusual configuration on this system, but this does work everywhere else I've seen (including other intel cards on other systems):
I have an interface, with two vlans, eg:
eth0.10
eth0.11
If I configure eth0.10 with a specific mac address, it appears that something happens in the driver/hardware level that prevents the network card from receiving (tcpdump does not see them) packets with that source mac address, even when they are coming in vlan11
Running the latest driver (not the OS-included one): 1.6.42
OS is Ubuntu Linux, 14.04.5 with 4.4 kernel
Any idea how to disable this behavior?
Thanks,
-Adam
↧
Configure wake on magic packet from power off state (Wake on Lan)
Hi Guys
I have several hundred Lenovo M73 with Intel i217-V lan adapters I am wanting to configure WOL on.
When install drivers in this case 12.12.218.0 via SCCM, the option "Configure wake on magic packet from power off state" is not enabled. When manually enabling this Wake on Lan works perfectly.
I have not been able to find a simple way to bulk enable this, I did find this ageing link however "prosetcl" does not seem to be installed anymore leaving me to believe there is another way?
Wake on Magic Packet from power off state
Can someone please explain how to remotely configure this via GP, registry or script.
Cheers
Simon
↧
I210 Multiple VLAN on Windows Server
Hello,
Is it possible to have multiple VLAN ID in Intel I210 network card on Windows Server 2016 ?
I installed the Intel drivers but apparently you can only define one VLAN ID?
Pilote version : 12.15.184.0 (04/08/2016)
Thanks for you help
Best Regards,
Fabien
↧
↧
VLAN adapter not working after reboot - Win10, 22.0.1
Following all the events at I211/I217-V Windows 10 LACP teaming fails and networking - USB to Ethernet adapter supporting multiple virtual LANs - Hardware Recommendations Stack Exchange, we now have an Ethernet driver that should properly support the Intel Advanced Networking Suite (iANS) under Windows 10.
Using Windows 10.0.14393 with all updates installed, with an I217-LM adapter and the 22.0.1 driver installed. Things seem to be very flaky. My focus here is primarily on being able to work with multiple VLANs, with no trunking at present.
First - when creating new VLANs, ensure that the "Network Connections" window or any similar windows other than the "Intel(R) Ethernet Connection * Properties" dialog are closed. Not doing so will frequently result in the operation hanging indefinitely. (I remember the same from when we had the working drivers here in Windows 7 and Windows 8 days.) Even with the other windows closed, sometimes it is taking almost 5 minutes to create a new VLAN - but it takes even longer to do so with the "Network Connections" window open (if it completes at all).
With this out of the way: Add a new VLAN10. Only once one VLAN is created can we then create the "Untagged VLAN" (ID 0). Reboot. Everything still works and comes back up as expected.
Add a 2nd tagged VLAN, say VLAN11. Reboot. The "Untagged VLAN" fails to pull a DHCP lease. The virtual adapter shows packets being sent and received. I ran Wireshark on the Untagged VLAN adapter, saw DHCPDISCOVER packets go out, and other unrelated broadcasts and packets coming back - but no DHCPOFFERs returned. I.E., it seems to be missing traffic in that state. Disable the Untagged VLAN adapter, re-enable, and it instantly comes back with a valid lease. This is constantly repeatable. Nothing is even connected to the other side of these VLANs yet (the connected switchport isn't even trunked). Remove the 2nd tagged VLAN leaving only one tagged VLAN and the untagged, and things work much better - but this kind of defeats the purpose.
Here's my ugly hack of a work-around for now: Add a Windows Scheduled Task to run at System Startup, and to run with highest privileges. Use a PowerShell similar to the following as the action:
$( Get-Date Write-Host "Starting..." ipconfig.exe /all Write-Host "Restarting..." Restart-NetAdapter -Name "Ethernet - Untagged" -Confirm:$false ipconfig.exe /all Get-Date Write-Host "Done." ) *>&1 > C:\FixIntelNetwork.log
I was worried about timing, and could add a 30 second delay or such in the startup trigger. However, the ipconfig outputs show that this wasn't necessary. In the first ipconfig output, the adapter was present and already had an auto-configured 169.254.x.y IP address. In the second ipconfig output, a proper DHCP lease was shown.
As I don't have anything on the other VLANs to test with yet, I still need to determine - but may have to reset the other VLAN interfaces at startup as well.
↧
intel nic drivers 19.3 huge 6000+ dpc latency spike once a few secs
hi, i would like to report that the new intel nic drivers version 19.3 that just released recently has huge 6000+ dpc latency spike once in a few secs.
my specs
Intel(R) 82579LM Gigabit Network Connection
windows 7 SP1 32bit + lastest windows update
i downgrade to intel nic drivers previous version 19.1 and the problem is just gone.
↧
VLAN creation on Windows 10 Enterprise TP
Hello, there.
This morning I upgraded my fully functionnal Windows 8.1 Enterprise installation to Windows 10 Technical Preview. Before that, I downloaded the Intel Network Adapter Driver from this website, version 20.1, for Windows 10 64 bits. After the driver installation, I had the VLANs tab in the network card properties. However, i'm unable to create a VLAN. The network card is automatically disabled then I receive an error message saying this (translated from french):
One or more vlans could not be created. Please check the adapter status and try again.
The window freezes and I have to force-close it. 802.1 option is of course enabled in the Advanced options tab. The event viewer always shows the same error when I try to create a VLAN:
Nom de l’application défaillante NCS2Prov.exe, version : 20.1.1021.0, horodatage : 0x554ba6a4
Nom du module défaillant : NcsColib.dll, version : 20.1.1021.0, horodatage : 0x554ba57d
Code d’exception : 0xc0000005
Décalage d’erreur : 0x0000000000264064
ID du processus défaillant : 0x19d4
Heure de début de l’application défaillante : 0x01d0ada33fd50576
Chemin d’accès de l’application défaillante : C:\Program Files\Intel\NCS2\WMIProv\NCS2Prov.exe
Chemin d’accès du module défaillant: C:\WINDOWS\SYSTEM32\NcsColib.dll
ID de rapport : eefb5842-9220-4bad-93d3-774828c5736e
Nom complet du package défaillant :
ID de l’application relative au package défaillant :
I already tried to uninstall all the packages and drivers related to the network card. I deleted fantom network cards then cleaned up the registry. I tried to set some compatibility options to the given executable file, with no success. I tried to reinstall the driver with Drivers Signature disabled, tried to disable IPv4/IPv6 from the network card before trying to add a VLAN... I tried everything I found on Google.
Could someone help me, please?
↧
Intel 82579v - Code 10 - media disconnected
After long shutdown and then power up ( eg. Power up in morning ) 82579v adapter shows Windows driver code 10 - with media disconnected status in ipconfig.
Shutdown and restart does not fix. Hard power off while machine running, wait 60 seconds and power on usually fix. Bio reset default also fix.
Problem re-occurs if machine is shutdown and powered off for a few hours.
It is not cabling or router since problem is resolved by one of the above power cycle steps.
Configuration:
Motherboard: Asus P8Z77-V Pro
Bios: Asus 2104 ( latest )
OS: Windows 10-x64
Network Driver: Intel 12.5.31.4 / ProSet 21.1.30.0
Applied NVRam update ( 82579VSKU ) adapter is now 82579V - no longer bounces to LM.
Tried:
Older BIOS
Microsoft Windows 10 Driver
Problem appears similar to:
↧
↧
Internet keeps dropping, Win10
Hi,
My internet keeps dropping every 10 minutes or so, it's a new computer with an ASRock B250M Pro4 motherboard, and a wired ethernet connection. My phone does not have any problems with the same router, neither did my previous computer.
I've read a bunch of solutions around the web, the main one is to go to Device Manager -> the network adapter -> Properties -> Power Management, and then turn off the "Allow the computer to save power" option.
This option wasn't there, and my settings looked something like this http://i.imgur.com/PBgPCSs.png which I assume is because the driver is newer than when that solution was proposed. I turned all the options in this dialog off, and it made no difference. I
I then installed several different versions of the drivers on the intel site, some with the "save power" option, and none of them stopped the issue from occurring.
What are my next steps?
↧
X710 L2 filter packet steering
Hello,
I am trying to use the x710 MAC/VLAN filtering option to steer packets to receive queues based on strict MAC address match.
I need to filter and steer around 100 MAC addresses to 8 receive queues. Because of the development environment constraints I cannot use
SRIOV, IOV, VEB or flex partitioning.
My configuration is as follows:
Default simple switch configuration
One PF and one VSI with 8 queues
RSS, Ether type and Flow director filters are disabled and MAC/VLAN filter is enabled.
I am setting toQueue flag to steer packets to the appropriate queue.
However I don't see packets getting steered to the desired queue. Packet steering is not happening and packets always land on the same queue.
Do I need to configure the switch with "Set Switch" command to get filtering work as described above?
How do I initialize the VSI to support the above flow.
Are there any other other configuration settings that need to be done to get the packets steered as described above?
Thanks,
Sony
↧
X550 Driver for Windows 10 (10.0.14393) WOL (Wake on LAN) not working
When I install the driver ver 21.1 Download Intel® Network Adapter Driver for Windows® 10 I get a message
"Important Note: Creating Intel® ANS teams and VLANs on Microsoft Windows® 10 is currently not supported. As a result, when created, teams and VLANs do not pass traffic. We expect that ANS will be supported on Microsoft Windows 10 client in a future release"
I dont need teaming etc...but once the driver is installed, I dont see WOL in the ADVANCED option ???
Where is the WOL feature???
Thanks,
↧
L2 VM using SRIOV with 82599ES
Hi,
I am trying to run a VM that wont have an ip address but instead will work in transparent mode (like a cable). I have a PF that has 7 VFs on it and some of these VFs are part of VLAN x and some VLAN y. Here are my issues:
1. I see that the bcast traffic is sent to all VFs regardless, can I change it so that only bcast for the related VLAN arrives on th VF?
2. As the traffic that I generate has a different dest IP/MAC than my transparent VM, the VF should be in promiscuous mode. Is it enough to set "trust on" with ip link?
What I am trying to do is, to pass the traffic from VM1 to VM2 over the transparent VM.
VM1 -- TransparentVM -- VM2
Thanks,
↧
↧
Intel Corporation 82599ES 10-Gigabit SPF/SFP+ cannot be identified in Suse 11 even there is ixgbe driver
not able to see the card, and I've got message as below
[ 5.920756] ixgbe: Intel(R) 10 Gigabit PCI Express Network Driver - version 3.19.1-k
[ 5.920786] ixgbe: Copyright (c) 1999-2014 Intel Corporation.
[ 5.920873] ixgbe 0000:03:00.0: PCI INT A -> GSI 40 (level, low) -> IRQ 40
[ 5.920908] ixgbe 0000:03:00.0: setting latency timer to 64
[ 5.938627] ixgbe 0000:03:00.0: failed to load because an unsupported SFP+ or QSFP module type was detected.
[ 5.938690] ixgbe 0000:03:00.0: Reload the driver after installing a supported module.
[ 5.938760] ixgbe 0000:03:00.0: PCI INT A disabled
[ 5.938830] ixgbe 0000:03:00.1: PCI INT B -> GSI 44 (level, low) -> IRQ 44
and there is something I find out from lspci commnad that the flag is not marked as bus master, so I am wondering if they are related
I also set allow_unsupported_modules=1, it seemed fine, but the cards cannot see the traffic
291 03:00.0 Ethernet controller: Intel Corporation 82599ES 10-Gigabit SFI/SFP+ Network Connection (rev 01)
292 Subsystem: Intel Corporation Ethernet Server Adapter X520-2
293 Flags: fast devsel, IRQ 40
294 Memory at d9080000 (64-bit, prefetchable) [size=512K]
295 I/O ports at ecc0 [size=32]
296 Memory at d91f8000 (64-bit, prefetchable) [size=16K]
297 Capabilities: [40] Power Management version 3
298 Capabilities: [50] MSI: Enable- Count=1/1 Maskable+ 64bit+
299 Capabilities: [70] MSI-X: Enable- Count=64 Masked-
300 Capabilities: [a0] Express Endpoint, MSI 00
301 Capabilities: [100] Advanced Error Reporting
302 Capabilities: [140] Device Serial Number 90-e2-ba-ff-ff-c0-cb-68
303 Capabilities: [150] Alternative Routing-ID Interpretation (ARI)
304 Capabilities: [160] Single Root I/O Virtualization (SR-IOV)
305 Kernel modules: ixgbe
↧
How to know the changeset of two different driver versions?
Hi,
For a study, I would like to know the differences between two Intel Network driver versions (example: delta changes/fixes/improvements from v18.6 and v21.1)
In the Intel websites, I don't get this information. can you please update from where can I get these information?
Appreciate your help!
↧
Pci-pasthrough and SRIOV on the same host
Hi,
Can i use PCI-Passthru and SRIOV on the same hosts for different ports? ens1f0-1 SRIOV with multiple VFs and ens2f0-1 pci-passthru ?
I have 2 apps on the same hosts one supports SRIOV and the other one only supports pci-passthru.
thanks,
↧