Hi.

So my problems is that with latest version of windows VLANS dont activate they stay disabled state, reinstalling drivers does nothing and they are newest version from intels website.

Ou snap

Message was edited by: Tiit Talts

Hi there,

we are experiencing problems with the X710 series R630 Intel NIC built-in within our Dell server (running ESXi version 6.5.0 / build number 7388607).

As for the i40en driver version:

   Driver Info:

         Bus Info: 0000:01:00:0

         Driver: i40en

         Firmware Version: 6.00 0x800034ef 18.3.6

         Version: 1.4.3

Just yesterday we had another outage with a lot of upset customer calls, so this issue is rather urgent. I have seen the blog entry for a i40en driver update for 6.7 installations, but that doesn't help our specific case.

Can you at least give us an ETA for the driver update for 6.5 installations? As mentioned above, it's pretty urgent as we can not have any more outages like yesterday. Please advise.

Thank you in advance!

Best

Tommy

Hi guys,

I can't get the created vlan(s) enabled. Their states keep showing "disabled" and the "modify" button is grey.

In the "network connections" page, the physical NIC icon is blue, but the virtual NIC(s) is grey.

Anybody has an idea what's going on here ?

Here are some related data:

* The notebook is Dell Latitude / Windows 8.1 pro up to date / 64-bit.

* No VM installed, virtualization is by default enabled at the bios, though.

* Adapter teaming is OFF by default.

* The wired NIC type is Intel i218-LM / ProSet version 23.2 the latest release.

* The ethernet properties have the default values. "Advance Network Services Protocol" will be checked automatically once I create a vlan.

Here are some taken actions:

1- tested out the trunk (tagged) port of the switch by using a macbook and a usb2eth adapter.

2- tried to create 1 vlan only and restart the notebook.

3- tried to create 2 vlans and restart the notebook.

4- tried to assign the virtual NIC ip addresses manually and dynamically.

5- tried to disable it and re-enable it manually from the "network connections" page.

6- tried to turn off the wifi and start all over again.

Thank you in advance !

Henry

hi.

can i use PCI EXPRESS INTEL QUAD LAN CARD 10/100/1000 Intel® Ethernet Server Adapter I350T4-V2 on windows 10 computer to accelerate the network comunication to the router?

hi intel corp  I will give you some ideas to help

why you don't make a new gaming modem you can see that netgear and other corps that make gaming modem but the gaming modem they make are not strong for real gaming always there problems always

I think is time intel that you can compete in gaming modem the true is that gaming modem technology is very weak for real time gaming networking for online multiplayer game that use heavy traffic network use

is time that you make something very power for gaming cable modem for that support all providers

here ideas of the gaming cable modems

make the modem support real speed for download and upload 10,000mb download and 10,000 upload

make something that can use a super fast memory of 1gb  ram or more

make a extreme super fast  cpu dedidcate it 6 or 8 core for the gaming modem  2.0ghz or higther

dedicate it 10 gigabit ports that support 10,000mbs

64 extreme  download  channels and 64  extreme upload channels

support all dosics up to 3.1 in download and upload too

make to select any channels download and upload to first star or change it

extreme next gen  wapa 3 wirless security and extreme speed

extreme turner modulation 10,000ghz that remove static,noise,and clean the signal ,and voltage protection

new futuristic desing for gamers

dedicate it motherboard and hardware for gaming

full firmware gaming software

internal speed test software too

…………………………………………..

next gen turbo custom firewall  so you can play with the firewall and be secure or disable and don't slowdown the network performance and speed

firewall ids ips  (https encription or highter security level )

next gen anti exploit tech

anti scrips attack protections

login modem https or highter to prevent hackers by pass the modem login

next gen ddos and dos attacks protections

turbo pakage deep inpection so the network don't slowdown

port scan protection

anti ramsomeware protection

web anti exploit protection

next gen network monitor to see all program and device and ect running  and see the speed of any device using and ect

make real time detections for applications and ect

make to enable or disable any device  or only the device you what to allow in lan network and wirless to be secure in both sides

make to detect ip conflict and fix it automatic

make next gen nat that have nat aceleration this will improve the network performance and security and that don't have conflict with other modems so you can open it and don't have problem in games

improve next gen comunication

improve next gen vpn  make turbo vpn and solid security

improve mac security to prevent hackers clone your mac address  and ip from your modem and devices

make a modem test this test is to detect if any part of the modem is not working or is damage by voltage or any part

make support for ip4 and ip6 in all the areas

make a new technology that the modem can scan multiple ip  and process the ip super fast this can reduce ping time when you will enter a website and gaming

make a new tech for network boost acceleration

improve 500% network stavility in all areas

prevent hakers enter remotely to the modem only the provider with a secure login

make the next gen firmware so you can update the modem with a secure firmware update  that don't infect with malware /and don't forget to always make update for the modem and improve ect

next gen turbo qos

make to change the modem ip login  incase you don't whant to be for example 192.168.0.1 you can change it to 192.200.01 this is example so you can change it to ect you whant

make to disable or enable any uknow ip or any ip

you can add a antivirus if you whant

add full 4k and 8k support for real speed

ect  this is your opportunity intel to start selling for the first time in history real solid gaming cable modems that support all providers

this will allow gamers have better connection and better stavility and security...…….. most gaming modem right now sucks

I am just helping think this is a good idea

add more features and ect

10-4 out

I've installed the driver PRO2K3XP_32 on HP Proliant ML350 Win 2003 Server, but the Intellan tree 1.3.6.1.4.1.343 is empty. How may I show the SNMP Lan Status?

Port State stays in Initializing state and not getting active

Omni-Path HFI Silicon 100 Series State: Initializing Physical state: LinkUp

# ibstat

CA 'hfi1_0'

        CA type:

        Number of ports: 1

        Firmware version:

        Hardware version: 11

        Node GUID: 0x00117501017bf382

        System image GUID: 0x00117501017bf382

        Port 1:

                State: Initializing

                Physical state: LinkUp

                Rate: 100

                Base lid: 0

                LMC: 0

                SM lid: 0

                Capability mask: 0x00410020

                Port GUID: 0x00117501017bf382

                Link layer: InfiniBand

#

4: ib0: <NO-CARRIER,BROADCAST,MULTICAST,UP> mtu 2044 qdisc pfifo_fast state DOWN qlen 256

    link/infiniband 80:00:00:02:fe:80:00:00:00:00:00:00:00:11:75:01:01:7b:f3:82 brd 00:ff:ff:ff:ff:12:40:1b:80:00:00:00:00:00:00:00:ff:ff:ff:ff

    inet 10.100.0.3/8 brd 10.255.255.255 scope global ib0

       valid_lft forever preferred_lft forever

Hello,

I have MSI x299 sli plus with I211 and I219-V

and since 2 to 3 weeks of connection problems to know more reception or upload for about 0.1ms.

This happens on both network cards randomly 1h like 10 minutes I tried also to go on a 4G connection and ADSL same symptoms.

The update of the drivers in 23.2 does not change anything and a complete reinstallation of windows 10 pro no change.

it's very annoying in online games if you have solutions ..

I have a Windows 10 system on Z370 chipset with INTEL® ETHERNET CONNECTION I219-V.

Latest drivers is installed.

When I'm trying to use "cast to" option, it falls with error "can't connect to device".

But when I insert additional USB Ethernet adapter, connect it to the same ethernet patch cord, option "cast to" works fine.

So, problem is in I219-V.

How ti fix this problem with DLNA casting?

Hi,

I recently build my PC and noticed a very strange problem..While my download speed is fine, my upload speed is almost 0. However using the same Ethernet cable on my laptop, upload speed is fine (~5-6 Mbps). So problem is not with the cable.

Things i tried:

- Reset modem -> do not work

- Update all drivers including the Intel Ethernet connection driver 1219 (version 12.17.10.7) -> do not work

- Ipconfig/release & renew -> do not work

- Disable all windows services and stop running programs -> do not work

- Change the intel ethernet connection driver settings to increase throughput -> do not work

Kindly help me to figure out what is happening? My last resort is to buy a PCI-E Ethernet card but want to try everything before doing that..

PC Specs:

- OS: Windows 10 64 bit Home Edition

- Motherboard: Asus Rog Strix Z370-H Gaming

- CPU: Intel i5 - 6400 8th Gen

- GPU: MSI Geforce 1050Ti (4GB DDR5)

- RAM: Patriot 8GB x 2 DDR4 2400Mhz

Hi, can anyone please advise if there is anything more I can do to fix lost ethernet after sleep mode?  I have updated the ethernet NIC driver to the latest 23.2 but the problem is still happening.  However I am not sure it has installed correctly as the driver properties show 12.15.31.4 (dated 25/07/2016) ??  Surely the driver should say 23.2?  The file PROWinx64.exe seems to have executed correctly without problems.   This problem started after the latest Windows update (April 2018).

When I come out of sleep, the adapter shows as Intel 82579LM, until I scan for hardware changes and it recognises it as 82579V.  This was the same problem as with the old driver, so the PROWin file hasn't changed anything.  Can someone please advise if the driver should say 23.2 in the network card properties?  Many thanks.

WIN 10 64-bit  (1803 latest edition)

ASUS P8z77 V-Pro motherboard (2012) - Latest BIOS

I've seen this posted on the forum a number of times, but there has been no posted solution. i have two know good 710 based network cards that have had their SPI flash chip replaced with a blank one. Now both cards are unable to be flashed with using the nvm utility. does anyone know the root cause of this? i am assuming since there is no firmware running from the SPI flash, that the nvm tool can not be used. does this mean that the SPI flash needs to be programmed manually?

Intel(R) Ethernet NVM Update Tool

NVMUpdate version 1.30.22.3

Copyright (C) 2013 - 2017 Intel Corporation.

WARNING: To avoid damage to your device, do not stop the update or reboot or power off the system during this update.

Inventory in progress. Please wait [+.........]

Num Description                               Ver. DevId S:B    Status

=== ======================================== ===== ===== ====== ===============

01) Intel(R) Ethernet Controller XL710              154B 00:001 Access error  

    Generic ID                                                 

Tool execution completed with the following status: Device not found

Press any key to exit.

My Environment:

Server: Fujitsu PRIMERGY RX2530 M4

Ethernet Adapters: Intel Ethernet Connection X722 LOM (Two SFP+ ports)

Ethernet Adapters Firmware: 3.51

--

ESXi: 6.5 U2

i40en driver version: 1.5.8

--

Both ethernet ports are connected to Juniper EX4550 Virtual Chassis (Junos version 12.3R9.4).

Switch ports are in trunk mode with native vlan.

--

After server boot up ESXi show only one X722 port which is online and port pass traffic. When I assign vlan tag to this interface (also changing ip addresses) then port is online but no traffic.

By default dcbx protocol is enabled on all switch ports:

set protocols dcbx interface all

I disabled dcbx protocol on ports where ESXi server is connected:

set protocols dcbx interface xe-0/0/15.0 disable

set protocols dcbx interface xe-1/0/15.0 disable

After server reboot ESXi show two X722 ports which are online and vlan tag assignment is working.

Is this the i40en driver problem?

Hi,

under the firmware version info, what does all three fields indicates.i think first one is firmware version, second one is ETrakID, What does the third field indicate ?

driver: i40e

version: 1.3.46.1

firmware-version: 5.05 0x80002927 1.1313.0

bus-info: 0000:08:00.0

supports-statistics: yes

supports-test: yes

supports-eeprom-access: yes

supports-register-dump: yes

supports-priv-flags: yes

I am planning to upgrade the firmware version to "5.40 0x80002d35 18.0.17", but i am not able to get the file. Is this specific to any vendor or any dependencies ?

-

Vishruth

Hi,

     I’ve come across a need to hotplug PCI devices between dom0 and domU using SR-IOV NIC. But I'm experiencing problems when trying to detach VF more than one PV guests.

I can attach VF  to DomU successful as follow:

# xl pci-assignable-list

0000:05:10.0

0000:05:10.2

# xl pci-attach 1 05:10.0

# xl pci-attach 2 05:10.2

But when I can't detach VF and it report errors as follow:

# xl pci-detach 2 05:10.2

libxl: error: libxl_device.c:1269:libxl__wait_for_backend: Backend /local/domain/0/backend/pci/2/0 not ready

And only 05:10.0 can detach successful :

# xl pci-detach 1 05:10.0

# xl pci-assignable-list

0000:05:10.0

Each guest config is the same like this:

name = "ubuntu-pv-1"

bootloader = "pygrub"

memory = 256

vcpus = 1

vif = [ 'bridge=xenbr0' ]

disk = [ 'file:/home/ye/ubuntu-pv/ubuntu-pv-1/ubuntu-pv-1.img,xvda,rw' ]

pci_permissive = 1

Follow xl dmesg log:

# xl dmesg | grep -i vt-d | grep -i enable

(XEN) Intel VT-d Snoop Control enabled.

(XEN) Intel VT-d Dom0 DMA Passthrough enabled.

(XEN) Intel VT-d Queued Invalidation enabled.

(XEN) Intel VT-d Interrupt Remapping enabled.

(XEN) Intel VT-d Shared EPT tables enabled.

# xl dmesg | grep "I/O virt"

(XEN) I/O virtualisation enabled

And libxl-driver log:

# cat  /var/log/libvirt/libxl/libxl-driver.log

xc: detail: sysctl operation failed -- need to rebuild the user-space tool set?

libxl: error: libxl.c:4364:libxl_get_physinfo: getting physinfo: Permission denied

xc: debug: hypercall buffer: total allocations:7 total releases:7

xc: debug: hypercall buffer: current allocations:0 maximum allocations:1

xc: debug: hypercall buffer: cache current size:1

xc: debug: hypercall buffer: cache hits:6 misses:1 toobig:0

I'm running in Ubuntu 14 using Xen-4.6. I have tested in other machine using the same environment but encountering the same problem.

Iam so dissappointed i left the stability of qualcomm network driver.

I have been running a KF2 Killing

floor 2 server for years.

Just recently i retired the gigabyte board and went with asus and the intel network drivers i have heard so much about!

Its been 4 mnths of torture trying to sort my high lag spike problem!!

Ping Spikes into the thousands every 5th or so refresh of server in game browser!!!

Yet when i start server on my old giga board the ping is steady!!

I want to break bones !!

How on earth do you release faulty drivers!!!

I finally thought i better atleast try ask and look for solutions in here , god knows ive looked everywhere!!!

NOT HAPPY.. intel LOLOL

i had better add... z370 asus rog strix i gaming crap, latest drivers and all dated drivers all bios now the latest .. attachment shows my 2 servers , ping spikes when running one server also.

Hi,

    I am using network performance measurement tool nuttcp with IGB and E1000 cards on one of my development boards.

Issue: Observed crash/watchdog bite using testing with both IGB and E1000 cards.

Kernel: kernel_msm-3.18

Steps to reproduce.

1.) On device:  ./nuttcp-8.1.4.arm -S

2.) On PC side run below command xxx.xx.xxx.xxx -> IP address of device.

./nuttcp-8.1.4.x86 -w2m -u -R 160M -i 1 -T 1m xxx.xx.xxx.xxx

3) After a couple of iterations we see the crash reported in the log.

IGB  Log

------------------

Parsing debug information for MSM_DUMP_DATA_CPU_CTX. Version: 20 Magic: 42445953 Source:

Parsing CPU1 context start 171c8a800 end 171c8b000

Core 1 PC: arch_counter_get_cntvct+1c <ffffffc000a25164>

Core 1 LR: arch_counter_get_cntvct+1c <ffffffc000a25164>

[<ffffffc000a25164>] arch_counter_get_cntvct+0x1c

[<ffffffc000352ca0>] __delay+0x24

[<ffffffc000352c74>] __const_udelay+0x24

[<ffffffc00049235c>] msm_trigger_wdog_bite+0xd0

[<ffffffc0000f1d0c>] spin_bug+0x94

[<ffffffc0000f1e7c>] do_raw_spin_lock+0x104

[<ffffffc000eb38a0>] _raw_spin_lock+0x28

[<ffffffc000710768>] igb_get_stats64+0x30

[<ffffffc000cb8244>] dev_get_stats+0x4c

[<ffffffc000d249f8>] iface_stat_fmt_proc_show+0x98

[<ffffffc0001e77e0>] seq_read+0x18c

[<ffffffc000222874>] proc_reg_read+0x8c

[<ffffffc0001c5fcc>] vfs_read+0xa0

[<ffffffc0001c6758>] SyS_read+0x58

[<ffffffc0000864b0>] el0_svc_naked+0x24

From the code, it looks like it could be stuck in igb_update_stats and so the unlock might not be happening in time.

Code file:/kernel_msm-3.18/kernel/drivers/net/ethernet/intel/igb/igb_main.c

5160static struct rtnl_link_stats64 *igb_get_stats64(struct net_device *netdev,

5161 struct rtnl_link_stats64 *stats)

5162{

5163 struct igb_adapter *adapter = netdev_priv(netdev);

5164

5165 spin_lock(&adapter->stats64_lock);

5166 igb_update_stats(adapter, &adapter->stats64);

5167 memcpy(stats, &adapter->stats64, sizeof(*stats));

5168 spin_unlock(&adapter->stats64_lock);

5169

5170 return stats;

E1000 Log

-------------

[  100.703446] init: Service 'atfwd' (pid 765) exited with status 255

[  100.708673] init: Service 'atfwd' (pid 765) killing any children in process group

[  104.343224] init: Untracked pid 2636 exited with status 0

[  133.202677] BUG: spinlock lockup suspected on CPU#0, kworker/0:3/986

[  133.208030]  lock: iface_stat_list_lock+0x0/0x18, .magic: dead4ead, .owner: NetworkStats/1294, .owner_cpu: 1

[  133.217936] Causing a watchdog bite!

[  133.345512] Backtrace for cpu 1 (current):

[  133.348758] CPU: 1 PID: 1294 Comm: NetworkStats Tainted: G        W      3.18.31-g12d3836-dirty #2

[  133.357697] Hardware name: Qualcomm Technologies, Inc. APQ8096v3 + PMI8994 DragonBoard (DT)

[  133.366028] Call trace:

[  133.368473] [<ffffffc000089d9c>] dump_backtrace+0x0/0x278

[  133.373843] [<ffffffc00008a034>] show_stack+0x20/0x28

[  133.378884] [<ffffffc000e70b08>] dump_stack+0x9c/0xd4

[  133.383914] [<ffffffc000093700>] arch_trigger_all_cpu_backtrace+0x6c/0xdc

[  133.390687] [<ffffffc0000f1e80>] do_raw_spin_lock+0x108/0x160

[  133.396415] [<ffffffc000e7f428>] _raw_spin_lock+0x28/0x34

[  133.401800] [<ffffffc0006d2de0>] e1000e_get_stats64+0x44/0x118

[  133.407614] [<ffffffc000c83140>] dev_get_stats+0x4c/0xac

[  133.412907] [<ffffffc000cef8f4>] iface_stat_fmt_proc_show+0x98/0x198

[  133.419243] [<ffffffc0001e77e0>] seq_read+0x18c/0x3b4

[  133.424277] [<ffffffc000222874>] proc_reg_read+0x8c/0xb4

[  133.429571] [<ffffffc0001c5fcc>] vfs_read+0xa0/0x14c

[  133.434520] [<ffffffc0001c6758>] SyS_read+0x58/0x94

cheers,

mohit

Hi Team,

Few nic ports are unable to initialize, please help to fix the issue.

Error Logs:

I was looking through the i40evf source code, and it seems like the maximum number of queues supported is 4. Is there a reasoning for this? Is there a way to use more, such as 16?

I've seen patches proposing removing a few variables (MAX_QUEUES, which sets the max to 16, but doesn't actually serve a purpose since the RX queues limit is set to 4).

Is possible that after 2 weeks intel ANS driver is still broken in win 1803? How many time i need to wait for this?

I can create the network LAG in LACP mode but i cant enable the interface. Is there any solution?